DIY Tub Installation.
DIY Tub Installation.
Blog Article
Listed here down the page you will discover a good deal of very good news in relation to A Step-by-Step Guide to Installing a Bathtub.
Mounting a bath tub isn't specifically brain surgery, however it does need solid plumbing, carpentry, and sometimes, tiling skills. Changing an old bath tub with a brand-new one is likewise a reasonably challenging project. If the old tub is readily accessible, the task can relocate immediately; if you need to open a wall to remove the old bathtub and also place the new bathtub, the job is much harder. In either case, the project is within a residence handyman's abilities, although you will need a helper to vacate the old bathtub as well as set in the brand-new one. See to it you have actually qualified yourself for the work as well as are comfortable attempting it. As opposed to employing a specialist to take over a halfway-completed task, it is far better to think about employing one prior to you start. Chances are you may require an expert plumber to make tube connections.
This write-up will certainly help you mount a new bathtub in your washroom if you have actually already acquired a new tub and also don't require to alter the arrangement of your previous water pipelines.
Your tools and also material checklist must comprise the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you need to do is detach the water. After doing so, switch on the faucets to drain any water staying in the system. The process of eliminating the existing taps can be rather problematic because of the restricted gain access to that is often the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a fabric all set for the continuing to be water that will originate from the pipes. When the supply pipes have been gotten rid of, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning during this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Before going on to fit the new taps, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and the other end supplies a link to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly require decreasing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin making sure that the washing machines remain in place between the tap as well as the sink. Protect the faucet in position with the manufacturer offered backnut. When the faucet is safely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical faucet adapters. The previous kind needs to be connected to the tap ends first, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Mounting the Bath tub
Making use of both wood boards under its feet, position the bath tub in the called for placement. The wood boards are helpful in evenly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 tiny factors.
The following objective is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the bathtub until the level reviews degree.
To mount faucets, fit the bottom of the furthest flexible tap connector to the appropriate supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Switch on the water supply and also examine all joints as well as new pipework for leaks and tighten them if necessary. Load the bath tub as well as likewise check the overflow electrical outlet and also the typical outlet for leaks.
Finally, deal with the bathroom paneling as explained in the producer's instruction manual. Tiling and also securing around the tub should wait till the bath tub has been used at the very least when as this will resolve it right into its final position.
Planning for the Setup
First of all, the sustaining framework supplied with the bathroom must be fitted (if required) according to the supplier's directions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to ensure that if the faucet includes a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets unit to stop stress on the bath tub.
Fit the versatile tap adapters to the bottom of the two faucets utilizing 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you utilize all of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must now be ready to be suited its final setting.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to crack a stiff seal, creating the water to pass through the wall between the bath and also the tiling, bring about complications with dampness as well as feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your components and also installations. They are sold in tubes and cartridges, as well as are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill up the tub with water prior to securing, to allow for the movement experienced when the bathtub remains in usage. The sealer can crack fairly early if you do not take into consideration this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water resistant sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our article about How to Install a Bathtub Yourself. Thanks a ton for taking time to browse our content. Enjoyed our posting? Please share it. Help other people locate it. Thank you for going through it.
Visit Homepage Report this page